Your cart: Items:, Value:

Glues Gels & Double Sided Foam for Gyro's etc

Model Helicopters  | Tools | General Tools | Hardware & Accessories |  Glues Gels & Double Sided Foam for Gyro's etc

Insta-Cure Super Thin CA 1/2 oz

Insta-Cure Super Thin CA 1/2 oz


Price: 3.55 / 4.40

Insta-Cure Super Thin CA 1/2 oz
INSTA-CUREhas a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

INSTA-CURE is a highly refined CA which, combined with its freshness, gives a guaranteed 2 year shelf life.

Insta-Cure Plus Gap Filling CA 1/2 oz

Insta-Cure Plus Gap Filling CA 1/2 oz


Price: 3.55 / 4.40

Insta-Cure Plus Gap Filling CA 1/2 oz
INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

Finish-Cure 20 Min Epoxy 4.5 oz

Finish-Cure 20 Min Epoxy 4.5 oz


Price: 5.99 / 7.43

Finish-Cure 20 Min Epoxy 4.5 oz
FINISH-CUREâ„¢ 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CUREâ„¢ can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, FINISH-CUREâ„¢ should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on FINISH-CUREâ„¢. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. FINISH-CUREâ„¢ is best mixed in a disposable cup.

Rating

Works very well. Very strong bond, takes a while to cure though, the 20 minutes refers to the amount of time you have from mixing to glueing the parts together. After its been glued together its best to wait at least an hour before stressing it.

TL-242 Thread Locker & Sealant Medium Strength

TL-242 Thread Locker & Sealant Medium Strength


Price: 2.50 / 3.10

TL-242 Thread Locker & Sealant Medium Strength
Easy removal, used for Fixing and sealing of threaded fastener size M6~M20

TL-271 Thread Locker & Sealant Ultra High Strength

TL-271 Thread Locker & Sealant Ultra High Strength


Price: 2.50 / 3.10

TL-271 Thread Locker & Sealant Ultra High Strength
High Viscosity, used for Fixing and sealing of threaded fastener size under M36.
For perminent locking of threads. Heat required to remove.

TL-609 Thread Locker & Sealant Ultra High Strength

TL-609 Thread Locker & Sealant Ultra High Strength


Price: 2.50 / 3.10

TL-609 Thread Locker & Sealant Ultra High Strength
Low Viscosity and good solvent resistance, used for Fixing and sealing components like shafts and bushings with transition and interference fit of radial dearance less than 0.1mm.


TL-262 Thread Locker & Sealant High Strength

TL-262 Thread Locker & Sealant High Strength


Price: 2.50 / 3.10

TL-262 Thread Locker & Sealant High Strength

TL-262 Thread Locker & Sealant High Strength
Fast cure time, used for Fixing and sealing of threaded fastener size M10~M20

TL-680 Thread Locker & Sealant Ultra High Strength

TL-680 Thread Locker & Sealant Ultra High Strength


Price: 2.50 / 3.10

TL-680 Thread Locker & Sealant Ultra High Strength

TL-680 Thread Locker & Sealant Ultra High Strength
Medium Viscosity and good solvent resistance, used for Fixing and sealing components like shafts and bushings with transition and interference fit of radial dearance less than 0.2mm.

T Rex Sticky Gyro Gel

T Rex Sticky Gyro Gel


Price: 6.45 / 8.00

Instructions:
?PU adhesive gel is a material that possess excellent vibration dampening characteristics, ideal for mounting gyroscopes, receivers, or other electronics in vibration prone areas. The gel can be re-used by cleaning off containment (such as dust) with water. Mild detergent can also be used to wash away oily residues. Once dried the gel will regain its adhesiveness. The PU adhesive gel is an ideal replacement for traditional gyro foam tape. Its excellent vibration dampening characteristic can minimize impact induced damages on electronics.

Specification:
?Material:PU
?Size:110x55x3mm

Accessories:
?PU adhesive gel x 1
?Hook & loop fastening tape x 2

PU Adhesive Gel
K10457A


PU Adhesive Gel for Gyro mount etc NOT BRANDED

PU Adhesive Gel for Gyro mount etc NOT BRANDED


Price: 4.99 / 6.19

PU Adhesive Gel is a material that possess excellent vibration dampening characteristics,ideal for mounting gyroscopes,
Receivers,or other electronics in vibration prone areas.The gel can re-used by cleaning off containment (such as dust)
With water. Mild detergent can also be used to wash away oily residues. Once dried the gel will regain its adhesiveness.
The PU Adhesive Gel is an ideal replacement for traditional gyro foam tape. Lts excellent vibration dampening
Characteristic can minimize impact induced damages on electronics.

Maxi-Cure Extra Thick CA 1. oz

Maxi-Cure Extra Thick CA 1. oz


Price: 3.65 / 4.53

Maxi-Cure Extra Thick CA 1. oz
MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic.
MAXI-CUREâ„¢ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CUREâ„¢ or any other adhesive. It also is best for bonding the tires for R/C cars.


Peel-n-stick foam tape. 10x 5inch 4mm thick

Peel-n-stick foam tape. 10x 5inch 4mm thick


Price: 2.55 / 3.16

Well, its not really tape, its a whole 10 x 5 inch sheet of double sided mounting foam.
Great for mounting gyros, servos, receivers and much more!
Made with super sticky hot-melt glue ensuring a secure contact with almost any surface.
Just peel and stick!

Size: 252 x 127 x 4mm (10 x 5 x 0.15inch)

SOON to Be in Stock 04-11-09 (aprox 15-10-09)

5 Minute Quality Epoxy Glue

5 Minute Quality Epoxy Glue


Price: 3.30 / 4.09

5 Minute Quality Epoxy Glue
Minute A/B Epoxy Glue.
A very high quality clear setting epoxy glue.
Excellent gap filling and bonding properties on almost all surfaces including delicate foam and hard to bond alloy.

Product comes in sealed air-tight packaging.
You wont find a better quality epoxy from China. In fact, its possible to find 20cent epoxy glues of the same size, however they dont dry clear and their holding strength and adhesion is very poor.
Our glue is produced by MIRA, one of Chinas leading glue manufacturers who supply glues to Chinas aerospace and civil engineering market, requiring strict quality and performance guidlines.
Save yourself the headache and only purchase quality glues.

An essential item for any building project and perfect for emergency in-field repairs

4min Epoxy Steel

4min Epoxy Steel


Price: 2.40 / 2.98

4 Minute A/B Epoxy Glue.
A very high quality epoxy for metal.
Excellent for repairing mount, gap filling & bonding properties on almost all surfaces including hard to bond alloy.
Can be drilled and used as a structural component when dry.

Model Helicopters  | Tools | General Tools | Hardware & Accessories |  Glues Gels & Double Sided Foam for Gyro's etc

Sportsmoto Ltd Company Number 6709642 Ltd in United Kingdom